find below a tabel with the parameters you can set in the Growatt SPF inverters.<\/p>\n\n\n\n
Column B is meant to be the menu where you can access this parameter. In some cases for 111 and 305 you have to hold arrow up and down at the same time in the inverter and press the menu number as password. There are some descriptions for now in german but I will update the list in the future.<\/p>\n\n\n\n
<\/p>\n\n\n\n
Parameter 25, 26 and 35 are not used or unknown for now. If you have further details for those parameters please report…<\/p>\n\n\n\n find below a tabel with the parameters you can set in the Growatt SPF inverters. Column B is meant to be the menu where you can access this parameter. In some cases for 111 and 305 you have to hold arrow up and down at the same time in the inverter and press the menu … <\/p>\nProgram<\/td> Menu<\/td> Description<\/td> <\/td><\/tr> 1<\/td> 000<\/td> Output source priority: To configure load power source priority<\/td> <\/td><\/tr> 2<\/td> 000<\/td> Maximum charging current:
set total charging current for
solar and utility chargers.
(Max. charging current =
utility charging current +
solar charging current)<\/td><\/td><\/tr> 3<\/td> 000<\/td> AC input voltage range<\/td> <\/td><\/tr> 4<\/td> 000<\/td> Power saving mode
enable\/disable<\/td><\/td><\/tr> 5<\/td> 000<\/td> Battery type<\/td> <\/td><\/tr> 6<\/td> 000<\/td> Auto restart when overload
occurs<\/td><\/td><\/tr> 7<\/td> 000<\/td> Auto restart when over
temperature occurs<\/td><\/td><\/tr> 8<\/td> 000<\/td> Output voltage
*This setting is only
available when the inverter
is in standby mode (Switch
off).<\/td><\/td><\/tr> 9<\/td> 000<\/td> Output frequency
*This setting is only
available when the inverter
is in standby mode (Switch
off).<\/td><\/td><\/tr> 10<\/td> 000<\/td> Number of series
batteries connected<\/td><\/td><\/tr> 11<\/td> 000<\/td> Maximum utility charging
current
Note: If setting value in
Program 02 is smaller
than that in Program 11,
the inverter will apply
charging current from
Program 02 for utility
charger<\/td><\/td><\/tr> 12<\/td> 000<\/td> Setting voltage point back
to utility source when
selecting \u201cSBU priority\u201d or
\u201cSolar first\u201d in program 01<\/td><\/td><\/tr> 13<\/td> 000<\/td> Setting voltage point back
to battery mode when
selecting \u201cSBU priority\u201d
or \u201cSolar first\u201d in program
01<\/td><\/td><\/tr> 14<\/td> 000<\/td> Charger source priority:
To configure charger
source priority<\/td><\/td><\/tr> 15<\/td> 000<\/td> Alarm control<\/td> <\/td><\/tr> 16<\/td> 000<\/td> Backlight control<\/td> <\/td><\/tr> 17<\/td> 000<\/td> Beeps while primary
source is interrupted<\/td><\/td><\/tr> 18<\/td> 000<\/td> Overload bypass:
When enabled, the unit
will transfer to line mode
if overload occurs in
battery mode.<\/td><\/td><\/tr> 19<\/td> 000<\/td> C.V. charging voltage.
If self-defined is selected
In program 5, this
program can be set up<\/td><\/td><\/tr> 20<\/td> 000<\/td> Floating charging voltage.
If self-defined is selected in
program 5, this program
can be set up<\/td><\/td><\/tr> 21<\/td> 000<\/td> Low DC cut-off voltage.
If self-defined is selected in
program 5, this program can
be set up.
Low DC cut-off voltage will
be fixed to setting value no
matter what percentage of
load is connected.<\/td><\/td><\/tr> 22<\/td> inactive<\/td> Solar Balance SbE enabled (max charge plus loads) \/ Sbd disabled (max charge only)<\/td> <\/td><\/tr> 23<\/td> 000<\/td> AC output mode
*This setting is only
available when the inverter
is in standby mode (Switch
off).
Note: Parallel operation
can only work when battery
connected<\/td><\/td><\/tr> 24<\/td> inactive<\/td> NEC disable\/enable closes dry contact on battery \/opens relay on utility<\/td> <\/td><\/tr> 25<\/td> <\/td> <\/td> <\/td><\/tr> 26<\/td> <\/td> <\/td> <\/td><\/tr> 27<\/td> 111<\/td> CAP (Inverter Capacity)<\/td> <\/td><\/tr> 28<\/td> 000<\/td> Address setting
(for expansion)<\/td><\/td><\/tr> 29<\/td> 111<\/td> Grdv (vermutlich Grid Voltage)<\/td> Offsetwert um die Netzspannung zu kalibrieren<\/td><\/tr> 30<\/td> 111<\/td> bat.v (Battery Voltage Offset)<\/td> braucht man wenn die Bat V im Lastzustand bei mehreren parallelen Ger\u00e4ten unterschiedlich ist hab ich probiert und tut genau das was ich beschreibe…<\/td><\/tr> 31<\/td> 111<\/td> INv (vermutlich Invertervoltage Offset)<\/td> (vermutlich Invertervoltage Offset)<\/td><\/tr> 32<\/td> 111<\/td> OUtv (Output Voltage Offset)<\/td> vermutlich auch ein Offsetwert f\u00fcr die abgebene AC Spannung<\/td><\/tr> 33<\/td> 111<\/td> Pvv (PV Voltage)<\/td> vermutlich auch ein offsetwert f\u00fcr den PV Spannungseingang<\/td><\/tr> 34<\/td> 305<\/td> RST parameter reset<\/td> <\/td><\/tr> 35<\/td> <\/td> <\/td> <\/td><\/tr> 36<\/td> LI- P5<\/td> Battery Protocoll CAN\/RS485<\/td> <\/td><\/tr> 37<\/td> 000<\/td> Real time setting—Year<\/td> <\/td><\/tr> 38<\/td> 000<\/td> Real time setting—Month<\/td> <\/td><\/tr> 39<\/td> 000<\/td> Real time setting—Date<\/td> <\/td><\/tr> 40<\/td> 000<\/td> Real time setting—Hour<\/td> <\/td><\/tr> 41<\/td> 000<\/td> Real time setting—Minute<\/td> <\/td><\/tr> 42<\/td> 000<\/td> Real time setting—Second<\/td> <\/td><\/tr> 43<\/td> 000<\/td> Battery equalization<\/td> <\/td><\/tr> 44<\/td> 000<\/td> Battery equalization
voltage<\/td><\/td><\/tr> 45<\/td> 000<\/td> Battery equalized time<\/td> <\/td><\/tr> 46<\/td> 000<\/td> Battery equalized timeout<\/td> <\/td><\/tr> 47<\/td> 000<\/td> Equalization interval<\/td> <\/td><\/tr> 48<\/td> 000<\/td> Equalization activated
immediately<\/td><\/td><\/tr> 49<\/td> 000<\/td> Utility charging time<\/td> <\/td><\/tr> 50<\/td> 000<\/td> AC output time<\/td> <\/td><\/tr> 51<\/td> 111<\/td> FrSt dis<\/td> ???<\/td><\/tr> 52<\/td> 111<\/td> PvIS dis<\/td> ???<\/td><\/tr> 53<\/td> 111<\/td> EtL<\/td> ???<\/td><\/tr><\/tbody><\/table><\/figure>\n","protected":false},"excerpt":{"rendered":"