While printing again a lot of things these days and having a thermal cam in place I have to admit that the motors getting quite hot. I already changed the fan on the extruder motor but even the axis motors getting quite hot and scratching at the max operating temperature defined from the manufacturer Moons. I decided to add passive coolers to my high temp filament printer and will test the next few days how the modified cooling performs.
The difference of the z-axis profile length I explained in another post is only 2mm but led me to another conclusion about the belt drive. While the belt drive system on the MK3 has a self tensioning function realized in the grey plastic cap with a spring the MK2 version doesn´t have this. Due to this fact the belt on the MK2 has to be mounted already with tension to prevent backlash in the movement. Exactly this leads to the length difference of the aluminium profile. If anybody knows some preferences of the spring I would be happy to know and reorder.
Another thing I struggled was the length of the z-axis. Tiertime provides in their forums most of the printable parts as STL files. So I printed the version for the MK3 in the hope that it will fit on the MK2. Both constructions seem the same at the first view. My z-axis top part didn´t fit properly so I tried to find out what´s wrong after a while I realized that the 60×20 aluminium profile itself compared to the MK3 differs in the length. There is a difference about 2mm which leads to a different switching point of the microswitches. So I decided to adjust this manually to get the printer ready again.
MK2 below 196mm
This weekend I took some of my free time to bring my MK2 Cetus to the newest parts. As some of you might know I have a modified Cetus MK2 and a modified MK3 here. Both look the same but have slight differences construction wise which doesn´t make it possible to upgrade easily a MK2 to a MK3.
Z-axis one way clutch bearing.
Both the MK2 and the MK3 have a one way needle bearing installed on the z-axis motor shaft. I´m not sure if the MK1 had this also so this is only one finding from yesterday on my printers.
This bearing should prevent the axis falling down and crashing the build plate in case of emergency stop of the board or power loss of the motors. What I realized that the bearing on the MK3 behaves much different and slowly let the axis fall down when the board is shut down or motor off command is sent. A long time ago I already tried to adjust the MK2 bearing to stop at the position when the z-axis motor is off but struggled with some issues after. It is indeed possible to hold the position of the Z-axis on the MK2 version but makes the axis behave like there is a backlash. Especially when the axis have to move short distances which happens at every print. The result with my tests at this time to adjust the bearing tension ends by loosing it again as the z-level was not pisitioned precisely anymore. Intersting fact here is that the MK3 positions great so there have to be differences which I figured out 2 days ago.
On the MK3 Tiertime used a different one way clutch bearing.
While the MK2 has a HF0406 needle bearing installed at the MK3 there is a HF0406-KF needle bearing supporting the z-axis. After some research i found out that the addition KF means that in the needle cage there are plastic springs added. So this is a special version of the HF0406. I ordered 2 parts of the KF version and will test the upcoming days to upgrade this useful function into the MK2 version.
The bearing doesn´t make much difference. The solution for preventing the Z-axis from falling down is to short the motor wires. This seems to happen at the MK3 in the mainboard.
MK2 HF0406 below
MK3 HF0406KF below
As I accidentially deleted last week all config files from the SD.card of my tinyfabbed Tiertime Cetus printer I took some Corona time the last few days to rebuild all config files for the upgraded Cetus printer. I use the heatbed with external controller board plus the tiertime CPU plus the tiertime TFT on a MK2 Cetus. It is mandatory to upgrade to physical endswitches!!!
find HERE a package with a working cetus setup file plus mypanel config and the mandatory cura (4.5) printer config. Hope that helps anybody out there.